Charles Owen Pro II Plus Jockey Skull PAS015: Silver
The groundbreaking Charles Owen Pro II Plus Jockey Skull is the only triple-standard, precision-fitting cross-country skull cap with a removable liner. Featuring a sized liner that allows for the closest, most customised fit yet, the Pro II Plus includes front and rear ventilation slots for superior cooling and a GRpx® technology harness for unsurpassed stability. With a liner that can be replaced when it has been broken down by wear cross-country, riders can easily refresh the life of their helmet.
00 1/2 – 6 or 52 – 65cm
Round Fit available: 1 1/2 – 3 or 56 – 59cm
PLEASE NOTE: We DO NOT accept any returns on riding hats for your safety. All riding hats we sell are brand new and never been used before. We highly recommend being fitted for a riding hat at a qualified retailer like ourselves. By purchasing a riding hat from us online you agree to these conditions.
Riding Hats Size Chart
Measure head circumference at widest point, one inch above the eye. We highly recommend you have your riding hat professionally fitted by a fully trained person. We must point out due to health and safety reasons we do not accept riding hats back. We do this so you know every hat we send out is brand new and has never been tried on by anyone else.
|Circumference||Hat Sizes||Skull Sizes|
|52cm||6 3/8||00 1/2|
|54cm||6 5/8||0 1/2|
|56cm||6 7/8||1 1/2|
|58cm||7 1/8||2 1/2|
|60cm||7 3/8||3 1/2|
|62cm||7 5/8||4 1/2|
Charles Owen Riding Hat User Guide
PLEASE READ THESE FITTING INSTRUCTIONS VERY CAREFULLY FOR MAXIMUM EFFICIENCY OF THIS HELMET.
- Make sure that the helmet is the correct size with a firm but comfortable fit. (WARNING) For children, never select a helmet that is too large on the basis that they will grow into it.
- Adjust the fit of the harness whilst wearing the helmet. Insert the buckle on the end of the chin strap into the clip on the harness. To tighten the chin-strap, pull the slack downwards through the buckle and then adjust the rear straps, until the helmet is firmly positioned on the head. If fitted with a draw lace, then adjust the lace at the back and knot securely until the helmet is firmly positioned on the head. To undo the chin strap, squeeze the two prongs on the buckle clip in towards each other to trigger the release mechanism.
- To fasten helmets with a metal hook and bar buckle, clip the free end over the hook. Slacken and tighten by means of the metal bar buckle, and position the ‘O’ ring up to the buckle. Press stud the leather above the hook if fitted. Adjust the lace at the back and knot securely. If the leather harness is fitted with an enclosed magnet tab, position the end clip over the hook. The magnet will clasp the hook and tab together.
- The helmet should not rock forwards or backwards excessively.
For adequate protection ensure that it is the correct size and fits snugly. Helmets can move more on your head when riding. In order to ensure that the helmet remains in position during riding, adjust the retention system to ensure that the movement of the helmet on the head is minimal, both for front-to-rear and side-to-side movement This helmet maybe partially destroyed or damaged by a severe blow, even though such damage may not be readily apparent. The helmet may, after receiving an impact, be damaged to the point that it is no longer adequate to protect the head against further impacts. Any helmet subjected to a severe impact should be replaced by a new one, as a subsequent impact may not give the wearer such adequate protection. No headgear can protect the wearer against all foreseeable impacts and under certain conditions riding accidents can lead to death, serious injury and long term disability. Helmets are not designed to protect the head in the event of crushing by a horse.
The materials used in this product do not cause skin disorders or are hazardous for the user health. If you experience any reaction during the use of this helmet then you should stop using it.
Storage, Use, Cleaning, Maintenance, Servicing and
Helmets should be stored at ambient temperature out of direct sunlight. This helmet is designed to absorb some of the energy of a blow by partial destruction of the shell or protective padding material or both. This damage may not be visible and therefore any helmet which suffers an impact should be discarded and replaced by a new one. This helmet should not be dry cleaned or exposed to solvents.
When to replace the helmet
Modern helmets do not deteriorate in a bag on the shelf. The helmet has a stored amount of protection which is used up when the head hits the ground; the damage will not be obvious in the majority of blows. A helmet should always be replaced if the rider has lost consciousness or suffered a severe headache after the blow. All other blows may have reduced the protection which may be required in the next fall. Remember the damage to the helmet is caused by the primary impact site and any contact with the horse. If a helmet has had no blows, then other factors should be considered: fit of the helmet, condition of the helmet, and out-of-date designs.
A helmet is designed to be weaker than your head. Do not do things to the helmet that you would not do to your head. Do not subject the helmet to temperatures above 50oC or below -20 oC. Do not store the helmet in direct sunlight. Cleaning of the interior should be done using Charles Owen helmet cleaning products, foamed detergents or shampoo and water followed by vacuum drying the lining. It is important to use the minimum amount of water as helmets are difficult to dry and easily become mouldy. With any cleaning agent, it is important to try a small section to establish any allergic reaction. After riding, leave the helmet in a warm dry place overnight. Do not dry in front of a fire or a radiator. Do not store it in a plastic bag before it is dry. This will reduce the risk of rusting the metal components. Mud on velvet is best left to dry and then brushed off. The pile of the fabric can be revived by holding the hat in steam from a boiling kettle (excluding Ayr8® Classic).
Suitable accessories and spare parts
Accessories not approved by Charles Owen COMFG Ltd may affect the functionality and the performance of the helmet.
Limit of use of PPE
This helmet is designed to be used whilst riding horses or ponies.
EU declaration of conformity can be accessed here www.charlesowen.com/ppe
See “When to replace the helmet.” Under normal usage, a helmet will last between three and five years. If you use the product more frequently, then the helmet may need replacing more often.
Type of packaging suitable for transport
The packaging should avoid the helmet being crushed and becoming wet.
The kitemark signifies that this helmet has been manufactured under the control of BSI (0086) MK5 8PP, UK.
The SEI logo signifies that this helmet has been manufactured under the control of the Safety Equipment Institute (USA).
This helmet has been manufactured by Charles Owen COMFG Ltd, Royal Works, Croesfoel Industrial Park, Wrexham, LL14 4BJ, UK
Click here for more information on our Click & Collect Service
Please note: We are currently unable to process any orders for delivery
We are only processing orders for Collect @ Store Only
You can return your item by post or bring it in store, please see below for the different methods.
Returning an item by post:
If you are unhappy with the goods received we will refund your order if it is sent back in new, resaleable condition within 21 working days of receipt. If we find that the product has not been returned to us in a fully resalable condition, we reserve the right to refuse a refund on an item, or deduct at least £10 or 50% of the original selling price from the refund amount, whichever is higher.
In the interest of providing a swift and seamless experience for our customers we can no longer accept items back for exchange. Instead, you will need to return your original order to us for a refund, and place a new order for the item you require on our website.
Please contact us first if your item is faulty as is some cases we may be able to resolve the issue without the need for returning the item
We suggest for your own protection you use 1st class registered post or a tracked delivery service from a courier so your return can be tracked in transit. Any refunds will be issued once we have received the goods, in the original condition within a maximum of 30 days. This refund only includes the total of goods sent not the delivery charge unless the item is returned within 14 days of delivery. Unless an error has been made on our part the customer will be liable for the cost of the return postage.
We will not charge a restocking fee for returned items.
Any goods with manufacturing faults on arrival will be replaced or refunded, we will cover return postage costs if a mistake has been made on our part, or your item is defective.
This does not affect your statutory rights.
Returning an item in-store:
You are free to return your item to us personally within 21 days if it is in a new, resaleable condition. Please return it with your paperwork and our staff can immediately issue an exchange for the item in a different size or colour or for a completely different item or issue a credit note. As our online and instore payment systems are not linked we will not be able to make a refund immediately. If you wish to receive a refund we ask you leave the item with us and we will process it within 7 days back to the original payment method.
Cancelling an order
You must inform us in writing, or in another durable medium, if you wish to cancel. This includes letter or email. A phone call is not acceptable. Please contact us as soon as possible to inform us that you wish to cancel you order, by e-mailing us using our contact us form. We regret that we cannot accept a cancellation after the 14 day notification period has expired.